Rock River Arms National Match 2 Stage Trigger - .154"
Details
Details
Features:
- Heat treated cast steel with phosphate coating
- Consistent and smooth two stage trigger pull
- Overall 4.5-5lb pull weight
- Standard curved trigger bow
- Fits AR-15 and AR-10 lower receivers with .154” diameter pin holes
- Perfect edition to your short barrel rifle, designated marksman rifle, or duty rifle
- Lightened hammer for decreased lock time
- Affordable upgrade over standard military trigger groups
Note: Trigger pull weights are approximate and may vary between rifles.
AR-15 rifles have become a staple in 3 gun competition, precision match shooting, and many other competitive environments due to the large amount of aftermarket parts and accessories available to customize your rifle. Whether you have your gun set up as an sbr, dmr, or dedicated race gun, it is vital that you have a high-quality trigger not only for accuracy and speed, but for safety as well. The Rock River Arms National Match trigger is designed to tick each of those boxes no matter how your AR is set up. It features a two-stage trigger pull with a .5lb first stage and a 4-4.5lb crisp break. The overall trigger pull is light and smooth which is much better alternative than a gritty Mil-Spec stock trigger. Not only is this trigger great for match shooting, it is a great trigger to put in your varmint or hunting rifle so you can be confident in your shot with this accuracy enhancing upgrade.
Rock River Arms has built their name on the idea of providing lawful United States citizens and law enforcement high quality AR-15’s and 1911’s. They have a large selection of parts, accessories, complete lower and upper receivers, and competition match ready components. RRA is owned and operated by the Larson brothers who have worked for high-end companies such as Springfield Armory and Les Baer Customs and brought their knowledge with them to Rock River.
Specifications
California Prop 65 warning
WARNING: This product can expose you to chemicals, which are known to the State of California to cause Cancer and Reproductive Harm. For more information go to www.P65Warnings.ca.gov.Ratings & Reviews
97 reviews
Rock River NM trigger
by Michael
For the 1st part, this trigger WILL NOT fit in an Anderson lower receiver. I have 2 and it would not fit in either one. I did install it in a Spikes lower and it went in without any problem. There are small differences in mil-spec regardless what anyone says. This trigger is a big upgrade over a mil-spec trigger, but it is not as smooth as the factory trigger a friend has in his factory Rock River Ar. I would imagine they do a little more work when they fit them at the factory. The trigger is OK, but next time I will spend the extra money and buy another CMC trigger. There is about $40 or $50 differnce if you shop the sales.
Buying decision
by Jack McElroy
After checking several sites, your price was the best, for the same product.Th trigger has been installed and makes a great difference in the feel of my AR-15.I have added your site to my Favorites list.Jack
Good Trigger
by theedweed
After installation I noticed a gritty 1st stage pull and a looong mushy reset. I took it to the range to break it in. After a couple hundred rounds there was no improvement with either issue. I sat in my chair that night and run it through a couple of hours worth of usage.I'm not a gunsmith and have limited knowledge of the fire control group, so I make no claims of knowing what I'm doing.I removed the parts which were coated in what appeared to be paint, but I doubt if it's paint. I did a little polishing on the hammer and sear, then reapplied a small amount of grease, the 1st stage take up got a little smoother.I did not attempt to change the reset. All of the parts have the same coating as the hammer and sear. I just hope that over time the reset will get a little more consistent and not have such a long travel.Much better than the stock DPMS it replaced. I kind of wish I would have spent the extra money and purchased a Geissele ssa-e.
GREAT TRIGGER
by Kelly Stewart
As far as I'm concerned, this is an awesome trigger, especially for the money. It has a great, crisp break and has worked really well in the two rifles I have put them in. Can't go wrong with this one.
Rock River Trigger
by Jim T.
Building a 300 Blackout and I've got this trigger on my Elite Rock River - will report back how well this worked in my first AR-15 build...
Damn nice trigger
by Paul C.
don't believe you can get a better trigger than this without dropping 3x more for a Geissele or Timney.
Great trigger, best price!
by Scott Y
Easy install, fantastic trigger, may even like it more than one twice its price.
.156 Pins Required
by Nicolas Corry
Edit to my May 2015 review- after shooting it for a while now and comparing it back to back with my SSA-Es, I gotta say that this is a very, very good trigger when used with the JP Enterprises 3.5lb spring set and the .1555 KNS pins. Very happy with it at about half price of the SSA-E. The description states "Fits AR-15 receivers with .154" hammer and trigger pins" but the instructions included state DO NOT USE WITH ANYTHING BUT .156" PINS. So, do I send the KNS normal .154" pins back, or send the trigger back and wait on the .1555" KNS set? The trigger surfaces came straight out of parkerizing and no stoning or similar work has been done. For the cost of shipping the trigger, JP Springs and KNS pins back, I'd have only been about $50 away from an SSA-E.
Great Service!!
by EDUARDO
Exactly what I was looking for.Great value, quick shipping easy to install thanks to a good set of instructions included in the package.Trigger works great. Excellent quality for the price.
Rock River 2 stage trigger
by Joseph Boyd
Fast shipping. Product packaged well and delivered in great condition. Made a huge improvement in my M&P 15 trigger.