Ghost Firearms No Logo M-LOK Handguard Black - 15"
- Hardcoat anodized black
- 6061-T6 series aluminum extrusion
- Free float handguard
- MIL-SPEC Picatinny rail
- M-LOK slots at the 3, 6, and 9-o’clock positions
- Clamp on system for easy assembly
- Steel barrel nut and screws included
- Inside diameter: 1.365"
- Made in the U.S.A.
Ratings & Reviews
DO NOT BUY IT!!!
by Joe -
DO NOT BUY! Sorry for using all capital words, but there’s how terrible it has. I bought two of them, ones 15” and ones 10”. They are very hard to locking tightly, what it means? The two locking pins( bottom postion near by the barrel nut, and that only it has)just can’t work well, I locked them in way, and tried to test how tight it’s, it looses and not stable. When I hold it a little bit over-strength, the handguard will be twisted and loose it’s postion, goes forward. Damn, price defines the quality, these words would never go wrong.
Don't waste your money
by Joe -
I bought two of them, 15'' and 12'' no logo freefloat handguard. Both are looking good but not for the quality. It only has two locking pins on the bottom position, which is under the barrel nut. Unfortunately, that two locking pins are too loose on their position, even i used overstrength on both pins. It's very easy to twist or going forward when i holding the handguard at fore-position tightly. Not suggested to buy, price matters.
I have not mounted any accessories on it yet, but the weight is minimal. The fit is perfect on my Radical upper, and it looks awesome.
Best bang for the buck
When I ordered this wasn't to sure how it was going to be for the price. When I received it in the mail and seen it in person it was very light. The barrel nut is different from what I seen but no big deal. When putting on the rail you will need a rubber mallet to make fit properly and does have anti rotation screws. Looks very nice on the gun. Yes I will be buying more for other builds.
Exactly what it says
Ordered this received in mail and was exactly what they said it was very light and has anti rotation screws and we'll need rubber mallet to put on properly
Best bang for the buck
by Rob -
I've bought a few of these and you can't beat the price. Easiest handguards to install. Never had an issue with the screws being under the barrel nut. Attach a one piece scope mount and tighten down.
grate price and quality .
by Emmet -
go this for my 20 inch ar15 build , I seen a lot of other M-Lok hand guaurds that looked a lot like this one and I found the price and quality of this hand guard to be just as good and this was a grate buy, Loved how my AR15 turned out
Light & easy to install!
This handguard is pretty lightweight. I wish i had a scale so i could weigh it. The steel barrel nut itself is heavier than the handguard. It all went together fairly easy. The back part of the NCStar armorers wrench was able to fit this barrel nut. Some reviews said that a rubber mallet was needed to put the handguard on the barrel nut. I didn't have this issue. It slid right on for me. Then tighten the 2 anti-rotation screws on the bottom with some blue loctite & good to go!
Good for a Budget Build
by Alexander -
Build quality is decent and finish is good enough to where your friends will want to shoot it and but you won't have to worry about them scratching it or dropping it like the idiot friends they are. Installing was easy and only needed a rubber mallet to lightly tap the hand guard onto the barrel nut. Snug tight fit and the screws finish the job tightening the hand guard good. Slight scratch on finish near the barrel nut, probably due to QC checking if the barrel nut and hand guard fit.
Decent Handguard for the price
by SJ -
I bought this on sale. It's well made, easy to install and solid. It's kinda heavy and not as ergonomic as some of the other choices out there.
Wouldnt do it...
by Cochran -
So I got this despite the 2 reviews that were negative and then I got the hand guard "installed" or what I thought was installed. The hand guard will twist no matter how much you tighten it. It does take a bit of force to do this but still.. really?.. No good.
Great for budget rifle
Great for the price! I have it on a 22lr build. I like it!
It just works ... What else do you need?
EXCELLENT light weight 15" rail. It looks good and is tough, it just works ... What else do you need?