Details
Details
The Bravo Company Manufacturing BCMGUNFIGHTER Mod 3 Grip is a polymer AR-15 pistol grip with a reduced grip angle to enhance ergonomics and improve trigger control. Optimized for modern rifle handling, the Mod 3 Grip provides a more natural wrist position that supports comfort and precision over extended periods of shooting. The Mod 3 profile features a wider body than the BCM Mod 0 and Mod 1, a high-rise beavertail back strap, and an extended forward tang that fills the gap between the grip and trigger guard. An internal storage compartment is accessible with a hinged trap door sealed with a water-resistant rubber gasket. Constructed from high-strength, impact-resistant polymer, this AR-15 pistol grip maintains structural integrity under hard use. Made in the USA.
Features:
- AR-15 pistol grip
- Reduced grip angle for improved ergonomics
- High-rise beavertail back strap
- Extended forward tang to close gap with trigger guard
- Impact-resistant polymer construction
- Color: black
- Internal storage compartment with hinged trap door and water-resistant gasket
- Made in the USA
Specifications
California Prop 65 warning
WARNING: This product can expose you to chemicals, which are known to the State of California to cause Cancer and Reproductive Harm. For more information go to www.P65Warnings.ca.gov.
Ratings & Reviews
39 reviews
Best bang for buck
by Steve
Nice, snug fit and love the bit of width on it. Swapped from the gen one gunfighter highly recommend. Magpul needs to hop off that high horse.
My favorite grip so far
by Nathan -
I can't say enough great things about this grip. I love the beaver-tail , the texture, the geometry, the "stippling " for improved grip, the storage, and the forward tang to close the gap between the trigger guard. At this low MSRP, I'd recommend at least trying it out.
Good grip, except for one thing
by Robert
Overall, this is a nice grip. It's a little big for my hand, but texture makes it easy to hold onto. My only complaint is that BCM charges extra for the bottom plug for their grips. That should be standard for all grips.
The perfect grip
by Chris -
I used the Magpul MOE grips until I found the BCM Gunfighter. This grip has the perfect texture and places your firing hand in the optimal position for modern shooting stances. It places your hand a little higher on the grip with the wonderful beaver tail. I like the Magpul but I found them a little too thick for my hand size. I even put it on one of my Block 1 clones when I usually leave the old A2 for clone correctness but these have been seen in the wild as well I'm sure. Try it you'll love it. BCM is the best value on the market.
I switched back to a Magpul
by Jack Crab -
I guess I don’t get the hype about BCM products. This was a bear to mount, the bolt is a flat head screw so positioning it was a bear, the release on the bottom to access the storage takes the strength of Zeus to activate. In all it looks nice and feels nice, just a pain in the back in most every other way. I don’t see me buying it again.
I love this grip
by HP22 -
I have several of these on different lowers and am slowly switching from Magpul to these. Why? I like the angle, I like the texture, I like the storage compartment, and it fits my hand absolutely perfectly. It’s obviously easy to install and holds the safety detent spring with no issues. 10/10 would recommend!
Great grip
by Dex -
No issues its BCM its made great and feels good in the hand.
Modification required
by Eric -
As some reviewers stated, the grip did not fully seat on 3 different mil-spec mfg lower. Around the trigger guard it needs to be sanded/modified to allow to seat. Also, the fitting is extremely tight on the lower grip mount. I'm pretty sure its width is smaller than the lower grip mount point.
I don't like modifying things to make things work. No issues with magpul/b5/stock
Doesn't fit, sanding prolly fix it
by Eric -
had to use rubber mallet to just to get it to fit on the lower,however, the beaver tail is not to spec. This keeps the rest of the grip to be flush with the lower. Additionally, the bolt is not aligned because of this.
I'm sure I could sand it down and get it to fit, but I shouldn't have to sand anything new that is mil-spec to mil-spec. stock grip, magpul grips all work just fine on my lowers.
Looking through other reviews, I saw couple others say the same thing about sanding.
BCM Gunfighter Mod3 Pistol Grip
by Jarhead
This is by far the best pistol grip for the AR in my humble opinion. The width and angle of this grip is ergonomically perfect. I use this pistol grip on all my AR builds. Thank you PA for great pricing. Semperfi