Primary Arms Flip To Side Magnifier Mount - Standard Height

Details

The Primary Arms Basic Flip to Side Magnifier Mount with thumb screw mount is perfect for placing a magnifier behind all standard height 30mm red dots, Micro dots, and reflex sights using a lower 1/3rd cowitness height. Once your magnifier is installed in the 30mm ring, simply pulling the magnifier to the rear unlocks the mount, allowing you to instantly choose between centerline and off-centerline positions. This tough mount features a lifetime warranty.

NOTE:This mount places the center of the magnifier 1.64 inches above the top of the 1913 Picatinny rail. The magnifier will NOT line up with raised base optics such as the 7mm extended base EOTechs!

Back

Specifications

BrandPrimary Arms

California Prop 65 warning

WARNING: This product can expose you to chemicals, which are known to the State of California to cause Cancer and Reproductive Harm. For more information go to www.P65Warnings.ca.gov.

Back

7/11/2021 12:57 pm PAMQF-01

Sturdy but difficult to use

by Carl -

The mount is sturdy and holds the magnifier securely. My complaint is that to flip to side takes a lot of effort compared to my sightmark mount

It was good to speak to you on this and please let us know if there is anything we may help you with.

Was this review helpful?

9/5/2021 6:02 pm PAMQF-01

Needed another 3x mount

by Shawn Singleton -

I have an aim point 3x with a swivel disconnect and it was loose. I was looking at all kinds of mount that were WAY more expensive. This worked out great just tough behind an eotech 512 because the controls are on the back but that’s not the mounts fault. Definitely work recommend this to everyone.

Was this review helpful?

10/4/2021 1:52 pm PAMQF-01

Great flip mount for magnifier

by Greg S. -

This thing installs easy. Flips side to side flawlessly. And is really simple to maintain. I’ll definitely be investing in a few more and replacing my old button release flips.

Was this review helpful?

11/30/2021 10:51 pm PAMQF-01

not bad

by john p -

i am sure i will eventually use but not for the magnifier junk i bought

Was this review helpful?

3/30/2022 12:59 pm PAMQF-01

Solid mount for the money!

by Eric R -

I purchased this mount to go with the Primary Arms 3x magnifier gen4. This is a solid mount that can be setup to flip to either side. A little stiff to manipulate at first but with time will break in nicely. Very happy with my purchase.

Was this review helpful?

5/5/2022 4:26 pm PAMQF-01

Gets the job done

by Mark W -

Decent inexpensive magnifier mount. Little bulky and pretty stiff to flip to the side out of the box but I sprayed a little lubricant on the spring and it loosened up enough where I can now manipulate it to the side while still holding up my AR. Before I lubed it I literally had to bring my AR down from firing position and really put some force behind it to flip it. All in all it’s not too bad.

Was this review helpful?

10/3/2022 6:05 pm PAMQF-01

Works

by Sharky -

Probably not as nice as the other named brands but it worked out pretty good for my aimpoint mag. Installation is easy and after breaking it in, it's working much better.

Was this review helpful?

10/20/2022 10:27 am PAMQF-01

PA Flip To Side Magnifier Mount Standard height

by Rich M. -

I needed to make sure that the magnifier would co-witness my PSA
SLX Micro Dred Dot sight. The customer service rep. made sure I had the part number to match up the pair. Awesome features with both Red Dot and Magnifier. I would buy it again!

Was this review helpful?

5/23/2023 9:21 pm PAMQF-01

Good mount

by IN -

It’s a good mount.

Was this review helpful?

7/16/2023 4:46 pm PAMQF-01

Does what it says on the tin.

by Moe Lester -

Nothing special about it, just a good, sturdy mount that (for me at least) retains zero. Would recommend.

Was this review helpful?